License Type: EvalRightToUse License State: Not in Use, EULA not accepted Evaluation total period: 8 weeks 4 days Evaluation period left: 8 weeks 4 days Period used: 0 minute 0 second License Count: 0/0 (In-use/Violation) License Priority: None Store Index: 7 Store Name: Built-In License Storage Notice above that it STILL says 'EULA not accepted'.
Ever since Cisco created IOS, they shipped it as a single image file. This made installation very easy as you just download an image, copy it to your router or switch and configure your device to boot using the new image. When you want a newer version you’ll have to download a new IOS image…there are no patches or bugfixes.
Performance License for 4321 up vote 1 down vote favorite I'am trying to install an FL-4320-PERF-K9 (Performance) License on an ISR4321 to increase throughput from 85 mbit to 100 mbit but it tells me that there is a better license installed already. License Installation Using the CLI First copy this license to the router's flash memory using the copy command and a TFTP server. Example: Router#copy tftp flash: Address or name of remote host [ ]? 10.0.0.1 Source filename [ ]? Uck9_license.lic Destination filename [uck9_license.lic]?
Ever since Cisco was founded there has been an IOS image for each model, but there’s a different IOS image for the different versions of each model.
Featuring license in stock Collectible Doll Dept 56 Gas Pump Vintage Collectible Collectible Plate Collectible Figurine Collectors Large Ship Bell Camel Jewelry Box. Hello Guys, We have just purchased two new 2nd IGR 3925 routers which came in apart of the 3925 Voice Budle/w/ PVDM3-64 FL-CME-SRST-25 UC License PAK x2. Details about ? Cisco 2951-V/K9 with VOICE License CISCO2951-V/K9 vpn router uck9 ? Be the first to write a review. ? Cisco 2951-V/K9 with VOICE License CISCO2951-V/K9 vpn router uck9 ?.
For example, the Cisco 1800 series integrated services router has the following models:
Uck9 License
1801,1802,1803 and 1805.
1811 and 1812.
1841
1861 and 1861E
You might think that there is one IOS image just for the “1800 series” but this is not the case. There are 4 different IOS image. The 1801, 1802, 1803 and 1805 share a IOS image, so do the 1811 and 1812. For the 1841 there’s a separate IOS image and the 1861 and 1861E also share an IOS image.
To make things worse, there are also different IOS images for the different feature sets. Depening on the features you require you have to pay for a certain IOS image. For example if you want to run a VPN you might require the “security features” or if you want to use your router for voice over IP you might need the “voice features”.
Here’s what it looks like:
This is an example of the different IOS images for one router model, let’s say the 1861. You can get the IP base image which has some basic features. If you want voice features then you can buy the IOS image with just the voice feature set or one of the images on the right side that also has other feature sets. Of course, the more feature sets the more expensive the IOS image will be…
This is how Cisco ended up with many different IOS images. Different models, feature sets and versions.
Nowadays Cisco ships a universal image that has all feature sets included. We still have different IOS images depending on the model and version, but nu longer different IOS images with feature sets. Instead of all these different IOS images there’s just one:
Purchase Uck9 License
When you buy a Cisco device nowadays it will include an IOS image that has all feature sets but you will have to unlock them.
Previously it was possible to download just any IOS image from the Cisco website. Once you have a CCO account with download access you could download whatever you want. The problem was that many Cisco customers would just buy a router with the IP base IOS image and download the most advanced IOS image for it. There was no check to see if you had permission to run the IOS image that you downloaded.
Since the introduction of the 1900, 2900 and 3900 routers Cisco introduced the universal IOS image. These newer routers called Integrated Services Routers Generation 2 (ISR G2) use these newer IOS images.
When you buy any of these routers it will run the IP Base image by default and if you want extra features you can unlock them with a license key. The feature sets are now called technology packages:
Enable Uck9 License
IP Base
Data
Unified Communitications
Security
IP Base has the default IOS commands. Data supports features like MPLS, ATM and some others. Unified Communications has voice over IP features and security offers the IOS firewall, intrusion prevention system, IPSEC, etc.
If you buy a router with one of these technology packages then Cisco will activate them for you in the factory. Of course you can always buy and activate them later too.
The technology packages can be activated manually but for customers with large networks Cisco also released an application called CLM (Cisco License Manager). This free tool runs on Windows and Linux and communicates with the Cisco product license registration portal on the Internet to install license keys on your devices.
Let’s take a look how we can activate a license for one of the technology packages manually!
The routers that support the new licensing model have a unique device identifier (UDI). This number is a combination of the product ID (PID) and a serial number (SN). You can view this number on your router:
The show license udi command gives us the PID, SN and UDI.
In order to proof that we paid for a license we need something called a PAK (Product Authorization Key). This PAK has a unique number and Cisco uses it to check what license you have bought.
This PAK will be connected to the UDI of the router to create a license key. This can be done by going to the Cisco Product License Registration Portal on the website where you enter the PAK and the UDI. Cisco will check if your PAK and UDI are valid and that you haven’t activated the PAK before for another router. If everything is OK, they will e-mail you the license key.
The next step will be to copy the license file to your router; you can use any method you like for this…TFTP, USB flash drive, etc. Once the license file is on your router you need to use the license install command to install it. Let’s see what licenses are active on this router:
First we’ll use the show license command to verify what licenses are enabled. This router only has the default IP base image and none of the technology packages are enabled right now.
You can also use the show license feature command. This gives a better overview of the technology packages.
Cisco Cme Srst License
Show version will also show you license information: